Product Description

Diavolino ("little devil") is a low-cost, easy to build Arduino-compatible development board. Diavolino has the form factor of an Arduino Duemilanove or Arduino Pro, but with nicely rounded corners and a striking appearance. It's a low-profile through-hole version, with a simplified design. It's based on a ATmega328P microcontroller, and comes pre-flashed with the Arduino bootloader. Open source design, with bare basics hardware.

Diavolino is sold as an easy to assemble "through hole" soldering kit [?]. Basic electronic soldering skill is required, and you provide the soldering tools: a soldering iron and solder, plus small wire clippers. Assembly time is typically 10-30 minutes, depending on configuration and soldering skill.

To load Arduino sketches onto a Diavolino, you'll need an FTDI USB-TTL cable (or an equivalent USB interface). Even if you need to deploy lots of boards, you'll probably only need one cable.

Here's what you'll find on the Diavolino circuit board:

• ATmega328P microcontroller, with Arduino bootloader
• Genuine 16 MHz crystal oscillator (better grade, 20 ppm)
• 3 mm diffused red LED (naturally!), ready for blink sketch
• Auto-reset circuit
• Reset button
• Wire jumper for optional USB power
• 6-pin header for USB-TTL cable
• Places to hook up to a battery box, complete with strain relief
• Locations for optional side socket strips, ICSP connector, and TO-92 regulator

Here's what you won't find on Diavolino:

• The USB interface chip-- again, that's why you need the cable.
• Advanced power management. Please provide power to Diavolino from one source at a time: battery, USB, or plug-in power supply.
• A separate 3.3 V regulator. Shields and accessories that require separate 3.3 V power may need assistance to work correctly.

Powering Diavolino

Diavolino can be powered from a FTDI USB-TTL-5V cable, if you hook up the wire jumper that connects that power source to the board's "Vcc" line.

You can also power the board through a 3xAA or 3xAAA battery box, or through a plug-in power supply. For most situations that require wall-plug power, we recommend to use a 5 V power supply. If you want to use a higher voltage wall wart (e.g., 9 V), then you'll also have to provide a voltage regulator to make the 5 V supply for the microcontroller.

Kit configurations

The battery holder is a 3xAA box with cover and switch. The battery holder has almost exactly the same footprint as the Diavolino board, and you can stick it on with double-sided foam tape if you're so inclined. It's a great setup for easy portable projects.

The socket strip set is a four-piece set of header sockets, two each 6-pin and 8-pin, that allow the board to interface with many existing Arduino accessories.

Additional resources

You may also want to download the Detailed assembly instructions (10 MB PDF) for the Diavolino.

Suggested Accessories for Diavolino:

FTDI USB-TTL Cable $20.00 each Add to cart

Socket set for Diavolino $2.00 Add to cart

5V 150 mA Voltage Regulator $2.00 Add to cart

5V 150 mA Power Supply $5.00 each Add to cart

You may also be interested in...

5 V Energy Star Power Supply	9 V Power Supply	AA and AAA Battery Boxes	Target boards for ATmegaXX8 microcontrollers
The Adafruit USBtinyISP kit	6-pin Headers	Preprogrammed Microcontrollers	Diavolino: PCB only

Or perhaps our other Arduino compatible kits:

Meggy Jr RGB Video Game Kit

Peggy 2 Light Emitting Pegboard kit

Peggy 2LE Kits

Bulbdial Clock Kits

The Original Egg-Bot kit: coming the Evil Mad Science shop, late summer 2010.

If you'd like more information, please sign up with our form below, and we'll let you know when the details are released.

Please note: This is a single-purpose short-term mailing list that will only be used for one or two pieces of e-mail, tops. Once when we announce kit availability and pre-orders, and again when kits start shipping from stock. (If you'd like to join our regular Evil Mad Science mailing list, please sign up here instead.)